Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for West Jordan Homeowners
Chimney repair in West Jordan usually starts with a problem you can see from the driveway or smell in the living room: a crack in the crown, a rusted cap, a stain spreading across the ceiling near the flue. Whatever brought you here, the fix starts with knowing what’s actually wrong. Our technicians have up to 8 years of experience, we work with the brands professionals trust (DuraFlex, HeatShield, Gelco, Copperfield), and we handle sweep, repair, and inspection under one roof so you’re not juggling three contractors. Same-day service is available, and the written estimate sets the final price. Call (877) 404-8451 and we’ll tell you what your chimney actually needs.
Chimney Cap Installation
Chimney Cap Installation is the fitting of a proper cover over the flue that keeps rain, snow, birds, and debris out while letting smoke escape. You need one when a flue is open to the weather, when birds nest in the chimney, or when a cheap hardware-store screen has rusted through. In West Jordan’s dry, windy valley, an open flue lets grit and moisture straight into the liner. We work with Famco and Copperfield caps sized to your flue and anchored to the crown, not wedged in place. Typical installation runs $250-$650 depending on flue count, cap style, and how much prep the crown needs. The estimate is free and sets the final price.
Stainless and Powder-Coated Caps
Stainless caps hold up far better than painted steel in a valley that swings from hard freeze to warm afternoon. Powder-coated options look cleaner on a visible chimney, but stainless is what we recommend when weather is the concern. Either way, the cap has to be sized correctly or it rattles loose in high wind.
Multi-Flue and Custom Sizing
Chimneys with two or three flues need a cap built to cover the whole crown, not one small screen per opening. We measure the crown, the flue spacing, and the clearances before ordering so the cap fits without drilling into the wrong spot. Custom sizing matters most on older masonry chimneys where nothing is square.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Chimney Cap Replacement
Chimney Cap Replacement is swapping out a cap that has rusted, warped, come loose, or no longer fits the flue it covers. It’s needed when you can see rust streaks down the chimney, hear the cap rattle in wind, or find pieces of screen in the firebox. A failed cap is a direct path for water into the liner and the framing around it, so it’s one of the cheaper repairs that prevents expensive ones. We pull the old cap, check the crown and flue underneath, and fit a new one sized correctly. Typical replacement runs $200-$550 depending on access and whether the crown needs patching first. Nothing is recommended without a look at what’s under the old cap.
Spotting a Failed Cap
Rust bleeding down the masonry, a cap sitting crooked, or a screen peeled back at the edges all point to replacement. Water stains inside the firebox after a storm are another sign the cap is no longer doing its job. A quick look from the ground tells you most of it.
What Replacement Includes
We remove the old cap, inspect the flue tile and crown, and set the new cap with proper anchoring. If the crown is cracked, we’ll show you the photo and tell you whether it needs attention now or can wait. You get a clear picture before anything is ordered.
Chimney Liner Installation
Chimney Liner Installation is fitting a new flue liner inside the chimney to contain heat, gases, and creosote safely. It’s needed when the clay tile liner is cracked, missing, or too small for the appliance, or when a wood stove or insert was installed without a proper liner. This is where safety matters most: a failed liner lets carbon monoxide and heat reach the framing, and that’s not a repair to postpone. We install DuraFlex stainless liners and use HeatShield for restoring damaged flues where a full reline isn’t required. Typical liner installation runs $2,200-$5,500 depending on height, liner type, and whether the flue needs prep. Call (877) 404-8451 for an exact quote – estimates are free.
When a Reline Is Necessary
Cracked or spalling clay tiles, a liner that’s too small for the appliance, or a chimney with no liner at all are the usual triggers. A camera inspection shows the condition clearly before we recommend anything. If the liner is sound, we’ll tell you so, and that’s the honest answer.
Insulated Versus Standard Liners
Insulated liners hold heat better, which helps draft and reduces creosote buildup during Utah’s cold swings. Standard liners are adequate for some setups but don’t perform the same on exterior chimneys. We’ll explain which fits your chimney, not which is easiest to sell.
Chimney Flashing Repair
Chimney Flashing Repair is fixing or replacing the metal that seals the joint between the chimney and the roof, which is where most leaks begin. It’s needed when you see water stains on the ceiling near the chimney, rusted or lifted flashing, or gaps where the roof meets the masonry. Flashing takes the worst of the freeze-thaw cycle in West Jordan, and once it lifts, water gets behind it fast. We reseal or replace the flashing, step it into the shingles properly, and check the counter-flashing against the masonry. Typical flashing repair runs $350-$900 depending on roof pitch and how much of the seal needs rebuilding. We show you photos of the joint before we quote.
Leak Symptoms to Watch For
Brown rings on the ceiling, damp masonry after a storm, or rust streaks on the flashing itself are the usual signs. Water often enters at the flashing and shows up somewhere else entirely. A camera inspection from inside the chase helps confirm where it’s coming in.
Flashing Versus Roof Leaks
Not every leak near the chimney is the flashing; some come from the roof itself. We check both so you don’t pay for flashing work that won’t solve the problem. If it’s a roofing issue, we’ll tell you plainly.
Chimney Crown Repair
Chimney Crown Repair is fixing the concrete top of the chimney that sheds water away from the flue and masonry below. It’s needed when the crown is cracked, crumbling, or pulling away from the flue, which lets water soak into the brick and freeze. West Jordan’s freeze-thaw swings split a bad crown open quickly, and the damage spreads downward from there. We patch minor cracks or rebuild a failing crown with a proper slope and overhang so water leaves the chimney instead of sitting on it. Typical crown repair runs $350-$1,200 depending on how much of the crown is rebuilt. The estimate shows you what we’re fixing and why.
Cracks and Spalling
Hairline cracks are common and can often be sealed before they spread. Crumbling concrete and flaking around the flue are signs the crown is past patching. Either way, you’ll see the photos before we recommend a rebuild.
Rebuilding a Failing Crown
A rebuild casts a new crown with the correct slope and a drip edge over the masonry. That overhang keeps water off the brick face instead of letting it run down and freeze. It’s a repair that protects everything below it.
Chimney Repair Companies
Chimney Repair Companies are the specialists you hire when your chimney needs structural work, and choosing the right one matters more than finding the cheapest. You need one when you’ve got masonry damage, a failed liner, or a leak that a general handyman couldn’t diagnose. A generalist may patch a crack without finding the leak behind it; a chimney-only specialist works with the tools and materials the trade actually uses. We work with DuraFlex, HeatShield, Gelco, and Copperfield because those are the materials professionals trust, and we handle sweep, repair, and inspection under the same roof. Typical repair work runs $350-$5,500 depending on the scope, and the written estimate sets the final price.
What to Ask Before Hiring
Ask whether the company does chimney work only, whether they carry proper insurance, and whether they’ll show you camera evidence before recommending a repair. Ask what brands they install, too; a specialist names them without hesitation. If the answers are vague, keep looking.
Why Chimney-Only Matters
A company that also does roofing, HVAC, and gutters splits its attention across trades. Chimney-only means every tool and every judgment call is focused on one system. That focus is what catches problems a generalist would miss.
Chimney Masonry Repair
Chimney Masonry Repair is fixing the brick and mortar of the chimney itself: repointing joints, replacing spalled brick, and rebuilding sections that have lost their integrity. It’s needed when mortar is crumbling out of the joints, brick faces are flaking, or the chimney leans from water damage over time. Utah’s freeze-thaw cycle is hard on masonry, and a chimney that soaks up water in the fall will spall by spring. We repoint with proper mortar matched to the brick, replace damaged units, and check the crown and flashing at the same time so the repair holds. Typical masonry repair runs $500-$3,500 depending on access and square footage. The estimate lays out what’s failing and what can safely wait.
Repointing Versus Rebuilding
Repointing handles joints that have crumbled while the brick is still sound. Rebuilding is needed when brick faces have spalled deep enough that the unit can’t hold mortar. We’ll show you which one your chimney needs.
Water and Freeze-Thaw Damage
Water is the slow destroyer of every masonry chimney, and Utah’s swings between freeze and thaw speed it up. Sealing the top, fixing the flashing, and repointing bad joints are how you stop it. Fixing masonry without fixing the water source just buys time.
Brands We Service
We work with DuraFlex and HeatShield for liner and flue restoration because both are built for the demands of a real chimney system, and our technicians know where each one performs best. DuraFlex stainless liners hold up where heat and moisture are the enemy; HeatShield restores a damaged flue from the inside when a full reline isn’t necessary. We also work with Gelco and Copperfield on caps, dampers, and the accessory-level details that protect the whole system. Knowing these products means we install the right one for your chimney, not the easiest one to source.
We don’t claim to be a dealer for any of them, and we won’t tell you a brand will fix a problem it wasn’t designed for. What we offer is judgment about which product fits the job, matched to what the trade actually uses. Whether you have DuraFlex, HeatShield, Gelco, Copperfield, or any other make, we can help.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- Ceiling or wall stains near the chimney. Water marks after a storm usually mean flashing, crown, or cap trouble. Left alone, that water reaches framing and insulation.
- Crumbling mortar or flaking brick. Spalling brick and mortar falling out of joints mean the masonry is failing. It gets worse through each freeze-thaw cycle, not better.
- A strong, smoky smell or draft problems. Backdrafting or a persistent creosote smell can point to a blocked or damaged flue. That’s a carbon monoxide concern worth checking quickly.
- Cracked or missing flue tiles. Visible cracks in the liner let heat and gases reach the framing. This is a safety stop, not a cosmetic fix.
- Rust on the damper or firebox. Rust inside the firebox usually means water is coming down the flue. It points to a cap or crown problem that needs fixing before the liner is damaged further.
Our Process, Step by Step
- 1
Free estimate and a conversation. We start by asking what you’ve noticed: smells, stains, drafts, noises. That context shapes what we look for. The estimate is free, and no work begins until you approve it.
- 2
Camera inspection of the flue and firebox. A video camera lets us see the liner, joints, and firebox interior without guessing. You see the same footage we do, which is how a recommendation earns trust.
- 3
A written scope with photo evidence. We put the findings in writing with photos: what’s failing, what’s sound, and what can safely wait. Nothing gets recommended without evidence you can see for yourself.
- 4
The repair, done with the right materials. Whether it’s a DuraFlex liner, HeatShield restoration, or crown rebuild, we use the materials the trade uses and match them to your chimney. The written estimate sets the final price.
- 5
Final check and a clear handoff. We verify the repair, check draft and clearances, and leave you with the report. You’ll know what was fixed and what to watch for.
How Much Does Chimney Repair Cost in West Jordan?
Chimney repair in West Jordan typically runs from about $200 for a cap replacement up to $5,500 for a full liner installation, depending on what’s actually failing. A typical cap replacement in West Jordan runs $200-$550; a flashing repair runs $350-$900; crown repair runs $350-$1,200; masonry repointing or brick replacement runs $500-$3,500; and a liner installation runs $2,200-$5,500. Those ranges reflect the local market for professional-grade materials like DuraFlex and HeatShield, not cut-rate substitutes.
What affects the price most is scope, access, and materials. A single-story chimney with a sound crown is a quick job; a tall chimney with a failed crown, bad flashing, and a cracked liner is several repairs stacked. Roof pitch and how high the chimney sits change labor, and a full reline costs more than repointing because it’s a safety-critical system.
How to avoid overpaying: get the estimate in writing, ask for camera evidence before approving a repair, and ask which brand and liner type is being installed. A company that can’t show you photos or name its materials is guessing. We include a camera inspection and photo report with the estimate so you’re deciding from evidence, not a sales pitch. And we’ll tell you plainly when a repair can safely wait.
A free estimate includes the inspection, the written scope, and the photo report. Nothing is ordered until you approve the price. Call (877) 404-8451 for an exact quote – estimates are free.
Our Service Area Near West Jordan
We handle chimney repair across West Jordan and the surrounding valley, including West Valley City, Salt Lake City, and Copperton to the north and west, plus Granite and Emigration Canyon up toward the foothills. To the south we work in Eagle Mountain and Pleasant Grove, and east toward Lindon and Vineyard. If you’re near any of these, we can get you on the schedule, and same-day service is available. For a closer look at our main line, see chimney sweep West Jordan, and if you’re comparing repair options in a nearby town, our chimney repair page for Eagle Mountain and our chimney repair page for Pleasant Grove cover the details.
Serving West Jordan, UT – Our Local Coverage Area
We serve West Jordan and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Chimney Repair in West Jordan
Chimney repair is fixing the parts of the chimney system that have failed, from the crown and cap to the flashing, masonry, and flue liner. It covers structural fixes, not just cleaning, and it’s usually triggered by visible damage or a leak. We inspect first, then repair only what the evidence shows. Call (877) 404-8451 for an exact quote – estimates are free.
Most repairs take a few hours to a full day, depending on scope. A cap replacement or flashing repair is typically a short visit; a liner installation or crown rebuild can take longer. We give you a realistic timeline in the written estimate before work starts. Call (877) 404-8451 to book an estimate.
Repair costs range from about $200 for a cap replacement to $5,500 for a full liner installation, with most routine repairs landing between $350 and $1,200. The final price depends on what’s failing, access, and the materials needed. The written estimate sets the final price, and estimates are free. Call (877) 404-8451 for an exact quote.
Yes, we install and service DuraFlex stainless liners and use HeatShield for flue restoration where a full reline isn’t needed. We also work with Gelco and Copperfield on caps and accessories. If your liner brand isn’t one we name, we can still help. Call (877) 404-8451 to talk through your setup.
Same-day service is available, and we dispatch Sunday through Friday, 7am to 7pm. We’re closed Saturday. We answer 24/7, so a call outside dispatch hours is booked into the next opening. Call (877) 404-8451 to schedule.
Warranty terms depend on the type of repair and the materials used, and we put them in writing with your estimate. Nothing is left to a verbal promise. Ask about it when we quote the job, and you’ll see the terms before you approve anything. Call (877) 404-8451 with questions.
Clear the area around the fireplace, move anything breakable off the hearth, and make sure we can reach the chimney from the roof side. If you have a wood stove or insert, let us know so we bring the right tools. That preparation keeps the visit efficient. Call (877) 404-8451 to confirm your appointment.
Schedule Your Chimney Repair Service in West Jordan Today
If your chimney needs repair, the first step is a free estimate with a camera inspection and a written scope, so you know exactly what’s wrong before anything is ordered. We handle sweep, chimney repair, and inspection under one roof, using the brands professionals trust, and we tell you what your chimney actually needs. Call (877) 404-8451. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. You can also reach us for a chimney sweep or a chimney inspection when it’s time for routine care.
Written by the team at Chimney Sweep West Jordan.