Chimney Repair in West Jordan, UT | Chimney Sweep West Jordan

Chimney Repair in West Jordan - Camera Evidence Before Any Quote

Liner and masonry work is where this trade gets a bad name, so nothing is quoted until you have seen the camera footage yourself. Then a written, itemized price with no scope creep.

Call to schedule your free estimate

Work is performed by our local vetted partner.

Free
Written Quotes
Licensed & Insured Written Quotes Free Estimates All Brands Satisfaction Guarantee

Work is performed by our local vetted partner.

Sweep & inspectionSweep & inspection
Caps & crownsCaps & crowns
Flue reliningFlue relining
Masonry repairMasonry repair
Gas fireplace serviceGas fireplace service
Every visit starts with

Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed

Worth knowing

Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.

Get your free estimate

Trusted Chimney Repair for West Jordan Homeowners

Chimney repair in West Jordan usually starts with a problem you can see from the driveway or smell in the living room: a crack in the crown, a rusted cap, a stain spreading across the ceiling near the flue. Whatever brought you here, the fix starts with knowing what’s actually wrong. Our technicians have up to 8 years of experience, we work with the brands professionals trust (DuraFlex, HeatShield, Gelco, Copperfield), and we handle sweep, repair, and inspection under one roof so you’re not juggling three contractors. Same-day service is available, and the written estimate sets the final price. Call (877) 404-8451 and we’ll tell you what your chimney actually needs.

Call (877) 404-8451

Chimney Cap Installation

Chimney Cap Installation is the fitting of a proper cover over the flue that keeps rain, snow, birds, and debris out while letting smoke escape. You need one when a flue is open to the weather, when birds nest in the chimney, or when a cheap hardware-store screen has rusted through. In West Jordan’s dry, windy valley, an open flue lets grit and moisture straight into the liner. We work with Famco and Copperfield caps sized to your flue and anchored to the crown, not wedged in place. Typical installation runs $250-$650 depending on flue count, cap style, and how much prep the crown needs. The estimate is free and sets the final price.

Stainless and Powder-Coated Caps

Stainless caps hold up far better than painted steel in a valley that swings from hard freeze to warm afternoon. Powder-coated options look cleaner on a visible chimney, but stainless is what we recommend when weather is the concern. Either way, the cap has to be sized correctly or it rattles loose in high wind.

Multi-Flue and Custom Sizing

Chimneys with two or three flues need a cap built to cover the whole crown, not one small screen per opening. We measure the crown, the flue spacing, and the clearances before ordering so the cap fits without drilling into the wrong spot. Custom sizing matters most on older masonry chimneys where nothing is square.

Explore

Styles & brands we work with

  • Sweep & inspection
  • Caps & crowns
  • Flue relining
  • Masonry repair
  • Gas fireplace service

Chimney Cap Replacement

Chimney Cap Replacement is swapping out a cap that has rusted, warped, come loose, or no longer fits the flue it covers. It’s needed when you can see rust streaks down the chimney, hear the cap rattle in wind, or find pieces of screen in the firebox. A failed cap is a direct path for water into the liner and the framing around it, so it’s one of the cheaper repairs that prevents expensive ones. We pull the old cap, check the crown and flue underneath, and fit a new one sized correctly. Typical replacement runs $200-$550 depending on access and whether the crown needs patching first. Nothing is recommended without a look at what’s under the old cap.

Spotting a Failed Cap

Rust bleeding down the masonry, a cap sitting crooked, or a screen peeled back at the edges all point to replacement. Water stains inside the firebox after a storm are another sign the cap is no longer doing its job. A quick look from the ground tells you most of it.

What Replacement Includes

We remove the old cap, inspect the flue tile and crown, and set the new cap with proper anchoring. If the crown is cracked, we’ll show you the photo and tell you whether it needs attention now or can wait. You get a clear picture before anything is ordered.

Chimney Liner Installation

Chimney Liner Installation is fitting a new flue liner inside the chimney to contain heat, gases, and creosote safely. It’s needed when the clay tile liner is cracked, missing, or too small for the appliance, or when a wood stove or insert was installed without a proper liner. This is where safety matters most: a failed liner lets carbon monoxide and heat reach the framing, and that’s not a repair to postpone. We install DuraFlex stainless liners and use HeatShield for restoring damaged flues where a full reline isn’t required. Typical liner installation runs $2,200-$5,500 depending on height, liner type, and whether the flue needs prep. Call (877) 404-8451 for an exact quote – estimates are free.

When a Reline Is Necessary

Cracked or spalling clay tiles, a liner that’s too small for the appliance, or a chimney with no liner at all are the usual triggers. A camera inspection shows the condition clearly before we recommend anything. If the liner is sound, we’ll tell you so, and that’s the honest answer.

Insulated Versus Standard Liners

Insulated liners hold heat better, which helps draft and reduces creosote buildup during Utah’s cold swings. Standard liners are adequate for some setups but don’t perform the same on exterior chimneys. We’ll explain which fits your chimney, not which is easiest to sell.

Chimney Flashing Repair

Chimney Flashing Repair is fixing or replacing the metal that seals the joint between the chimney and the roof, which is where most leaks begin. It’s needed when you see water stains on the ceiling near the chimney, rusted or lifted flashing, or gaps where the roof meets the masonry. Flashing takes the worst of the freeze-thaw cycle in West Jordan, and once it lifts, water gets behind it fast. We reseal or replace the flashing, step it into the shingles properly, and check the counter-flashing against the masonry. Typical flashing repair runs $350-$900 depending on roof pitch and how much of the seal needs rebuilding. We show you photos of the joint before we quote.

Leak Symptoms to Watch For

Brown rings on the ceiling, damp masonry after a storm, or rust streaks on the flashing itself are the usual signs. Water often enters at the flashing and shows up somewhere else entirely. A camera inspection from inside the chase helps confirm where it’s coming in.

Flashing Versus Roof Leaks

Not every leak near the chimney is the flashing; some come from the roof itself. We check both so you don’t pay for flashing work that won’t solve the problem. If it’s a roofing issue, we’ll tell you plainly.

Chimney Crown Repair

Chimney Crown Repair is fixing the concrete top of the chimney that sheds water away from the flue and masonry below. It’s needed when the crown is cracked, crumbling, or pulling away from the flue, which lets water soak into the brick and freeze. West Jordan’s freeze-thaw swings split a bad crown open quickly, and the damage spreads downward from there. We patch minor cracks or rebuild a failing crown with a proper slope and overhang so water leaves the chimney instead of sitting on it. Typical crown repair runs $350-$1,200 depending on how much of the crown is rebuilt. The estimate shows you what we’re fixing and why.

Cracks and Spalling

Hairline cracks are common and can often be sealed before they spread. Crumbling concrete and flaking around the flue are signs the crown is past patching. Either way, you’ll see the photos before we recommend a rebuild.

Rebuilding a Failing Crown

A rebuild casts a new crown with the correct slope and a drip edge over the masonry. That overhang keeps water off the brick face instead of letting it run down and freeze. It’s a repair that protects everything below it.

Chimney Repair Companies

Chimney Repair Companies are the specialists you hire when your chimney needs structural work, and choosing the right one matters more than finding the cheapest. You need one when you’ve got masonry damage, a failed liner, or a leak that a general handyman couldn’t diagnose. A generalist may patch a crack without finding the leak behind it; a chimney-only specialist works with the tools and materials the trade actually uses. We work with DuraFlex, HeatShield, Gelco, and Copperfield because those are the materials professionals trust, and we handle sweep, repair, and inspection under the same roof. Typical repair work runs $350-$5,500 depending on the scope, and the written estimate sets the final price.

What to Ask Before Hiring

Ask whether the company does chimney work only, whether they carry proper insurance, and whether they’ll show you camera evidence before recommending a repair. Ask what brands they install, too; a specialist names them without hesitation. If the answers are vague, keep looking.

Why Chimney-Only Matters

A company that also does roofing, HVAC, and gutters splits its attention across trades. Chimney-only means every tool and every judgment call is focused on one system. That focus is what catches problems a generalist would miss.

Chimney Masonry Repair

Chimney Masonry Repair is fixing the brick and mortar of the chimney itself: repointing joints, replacing spalled brick, and rebuilding sections that have lost their integrity. It’s needed when mortar is crumbling out of the joints, brick faces are flaking, or the chimney leans from water damage over time. Utah’s freeze-thaw cycle is hard on masonry, and a chimney that soaks up water in the fall will spall by spring. We repoint with proper mortar matched to the brick, replace damaged units, and check the crown and flashing at the same time so the repair holds. Typical masonry repair runs $500-$3,500 depending on access and square footage. The estimate lays out what’s failing and what can safely wait.

Repointing Versus Rebuilding

Repointing handles joints that have crumbled while the brick is still sound. Rebuilding is needed when brick faces have spalled deep enough that the unit can’t hold mortar. We’ll show you which one your chimney needs.

Water and Freeze-Thaw Damage

Water is the slow destroyer of every masonry chimney, and Utah’s swings between freeze and thaw speed it up. Sealing the top, fixing the flashing, and repointing bad joints are how you stop it. Fixing masonry without fixing the water source just buys time.

Brands We Service

We work with DuraFlex and HeatShield for liner and flue restoration because both are built for the demands of a real chimney system, and our technicians know where each one performs best. DuraFlex stainless liners hold up where heat and moisture are the enemy; HeatShield restores a damaged flue from the inside when a full reline isn’t necessary. We also work with Gelco and Copperfield on caps, dampers, and the accessory-level details that protect the whole system. Knowing these products means we install the right one for your chimney, not the easiest one to source.

We don’t claim to be a dealer for any of them, and we won’t tell you a brand will fix a problem it wasn’t designed for. What we offer is judgment about which product fits the job, matched to what the trade actually uses. Whether you have DuraFlex, HeatShield, Gelco, Copperfield, or any other make, we can help.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Signs You Need a Pro Right Now

  • Ceiling or wall stains near the chimney. Water marks after a storm usually mean flashing, crown, or cap trouble. Left alone, that water reaches framing and insulation.
  • Crumbling mortar or flaking brick. Spalling brick and mortar falling out of joints mean the masonry is failing. It gets worse through each freeze-thaw cycle, not better.
  • A strong, smoky smell or draft problems. Backdrafting or a persistent creosote smell can point to a blocked or damaged flue. That’s a carbon monoxide concern worth checking quickly.
  • Cracked or missing flue tiles. Visible cracks in the liner let heat and gases reach the framing. This is a safety stop, not a cosmetic fix.
  • Rust on the damper or firebox. Rust inside the firebox usually means water is coming down the flue. It points to a cap or crown problem that needs fixing before the liner is damaged further.

Our Process, Step by Step

  1. 1
    Free estimate and a conversation. We start by asking what you’ve noticed: smells, stains, drafts, noises. That context shapes what we look for. The estimate is free, and no work begins until you approve it.
  2. 2
    Camera inspection of the flue and firebox. A video camera lets us see the liner, joints, and firebox interior without guessing. You see the same footage we do, which is how a recommendation earns trust.
  3. 3
    A written scope with photo evidence. We put the findings in writing with photos: what’s failing, what’s sound, and what can safely wait. Nothing gets recommended without evidence you can see for yourself.
  4. 4
    The repair, done with the right materials. Whether it’s a DuraFlex liner, HeatShield restoration, or crown rebuild, we use the materials the trade uses and match them to your chimney. The written estimate sets the final price.
  5. 5
    Final check and a clear handoff. We verify the repair, check draft and clearances, and leave you with the report. You’ll know what was fixed and what to watch for.

How Much Does Chimney Repair Cost in West Jordan?

Chimney repair in West Jordan typically runs from about $200 for a cap replacement up to $5,500 for a full liner installation, depending on what’s actually failing. A typical cap replacement in West Jordan runs $200-$550; a flashing repair runs $350-$900; crown repair runs $350-$1,200; masonry repointing or brick replacement runs $500-$3,500; and a liner installation runs $2,200-$5,500. Those ranges reflect the local market for professional-grade materials like DuraFlex and HeatShield, not cut-rate substitutes.

What affects the price most is scope, access, and materials. A single-story chimney with a sound crown is a quick job; a tall chimney with a failed crown, bad flashing, and a cracked liner is several repairs stacked. Roof pitch and how high the chimney sits change labor, and a full reline costs more than repointing because it’s a safety-critical system.

How to avoid overpaying: get the estimate in writing, ask for camera evidence before approving a repair, and ask which brand and liner type is being installed. A company that can’t show you photos or name its materials is guessing. We include a camera inspection and photo report with the estimate so you’re deciding from evidence, not a sales pitch. And we’ll tell you plainly when a repair can safely wait.

A free estimate includes the inspection, the written scope, and the photo report. Nothing is ordered until you approve the price. Call (877) 404-8451 for an exact quote – estimates are free.

Our Service Area Near West Jordan

We handle chimney repair across West Jordan and the surrounding valley, including West Valley City, Salt Lake City, and Copperton to the north and west, plus Granite and Emigration Canyon up toward the foothills. To the south we work in Eagle Mountain and Pleasant Grove, and east toward Lindon and Vineyard. If you’re near any of these, we can get you on the schedule, and same-day service is available. For a closer look at our main line, see chimney sweep West Jordan, and if you’re comparing repair options in a nearby town, our chimney repair page for Eagle Mountain and our chimney repair page for Pleasant Grove cover the details.

Serving West Jordan, UT – Our Local Coverage Area

We serve West Jordan and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.

Frequently Asked Questions About Chimney Repair in West Jordan

Schedule Your Chimney Repair Service in West Jordan Today

If your chimney needs repair, the first step is a free estimate with a camera inspection and a written scope, so you know exactly what’s wrong before anything is ordered. We handle sweep, chimney repair, and inspection under one roof, using the brands professionals trust, and we tell you what your chimney actually needs. Call (877) 404-8451. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. You can also reach us for a chimney sweep or a chimney inspection when it’s time for routine care.

Written by the team at Chimney Sweep West Jordan.

Why West Jordan Chooses Chimney Sweep West Jordan

We set the standard for chimney repair in West Jordan.

Evidence Before Recommendations

Every sweep includes a camera inspection and a photo report. If we find something, you see it before we quote it - no repair is ever recommended on our word alone.

Licensed & Insured

Fully certified technicians who meet all local and state licensing requirements.

Upfront Pricing

No hidden fees, no surprises. You approve the price before any work begins.

Guaranteed Work

Every repair and installation is backed by our workmanship warranty and satisfaction guarantee.

How It Works in West Jordan

Getting your chimney repair handled is simple and fast.

1

Call or Request a Free Estimate

Tell us about your chimney repair needs and we provide an upfront, transparent quote with no obligation and no hidden fees.

2

We Book a Time That Works for You

A background-checked, certified technician arrives at the time we agree on.

3

Problem Solved, Guaranteed

We complete the job to your full satisfaction, backed by our warranty and satisfaction guarantee.

What happens when you call

  1. 1
    A real person answersNo phone trees. Talk to a local chimney repair pro.
  2. 2
    You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
  3. 3
    We come out and measureLicensed & insured, at a time that suits you. The visit and the quote are both free.
  4. 4
    You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.

What West Jordan Customers Say

Trusted by homeowners across West Jordan and surrounding areas.

★★★★★

"Crown was cracked and taking water. Repaired it rather than quoting a rebuild, which the previous company had pushed hard for."

Roger Barrett
★★★★★

"Creosote buildup was worse than I realized. He measured it, showed me the glazing on the flue with the camera, and was honest that we were closer to a chimney fire than I wanted to hear."

Michelle Padgett
★★★★★

"Swept it, capped it, and installed a proper damper. The downdraft smell in the summer that we'd lived with for years is gone."

Beatriz Vargas

Ready for Chimney Repair in West Jordan?

Call now for a free estimate, or request one below. Licensed, insured, and here with fast help in West Jordan.

(877) 404-8451

Request a Free Estimate in West Jordan

Tell us about your chimney repair needs. We'll respond within the hour.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Now
Local Service Coverage
Call Now - We Answer 24/7