Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Fast, Reliable Chimney Repair Across Salt Lake City
If your fireplace is smoking back into the room, or you’ve noticed loose brick and crumbling mortar on the stack above your roofline, you’re in the right place. We handle chimney repair in Salt Lake City for the older brick homes that make up so much of this city, and we do it by showing you what’s actually wrong before anyone quotes a repair. Our technicians have up to 8 years of experience working on the kinds of flues and stacks you find here. Call (877) 404-8451 and we’ll get you scheduled.
Why Salt Lake City Homeowners Call Chimney Sweep West Jordan for Chimney Repair
Salt Lake City has a lot of chimneys that were built for coal and later pressed into service for gas inserts and wood stoves, and that history is where most of the trouble starts. We work exclusively on chimneys – no roofing, no HVAC, no general handyman work – so every judgment call is made by someone who looks at flues and fireboxes every day. That focus matters when a stack has been modified more than once over the past century.
We work with the brands professionals trust: HeatShield and DuraFlex for relining and restoration, Gelco and Copperfield for the accessory-level details that keep a chimney system sealed and venting correctly. If a liner needs to come out or a crown needs rebuilding, we’re working with materials meant for the job, not hardware-store substitutes.
Every visit starts as a safety diagnostic. We inspect, we run a camera, and we show you the footage. Nothing gets recommended that you can’t see for yourself, and we’ll tell you plainly when a repair can safely wait. One call covers the sweep, the repair, and the inspection, so you’re not stuck coordinating between contractors who each blame the other for a draft problem.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Chimney Flashing Repair in Salt Lake City
Chimney Flashing Repair in Salt Lake City usually comes down to the freeze-thaw cycle: water gets behind the metal where the stack meets the roof, freezes overnight, and works the seal loose a little more each winter. When flashing pulls away, water runs straight down into the attic framing and the masonry instead of shedding off the roof. A typical flashing repair here runs $250 to $550, depending on how much of the existing flashing can be reused and how steep the roof pitch is. If you see staining on the ceiling near the chimney after a storm, get it looked at before the next freeze.
What We Look For at the Roof Line
We check the step flashing, the counter-flashing set into the mortar joints, and the sealant at the base. Lifted or rusted metal, gaps at the masonry, and water tracks on the sheathing all point to the same problem. We fix the flashing and re-seal the joint rather than smearing caulk over a failure that will reopen.
When Water Gets Behind the Brick
Flashing that’s failed long enough lets water soak the masonry, and that shows up as spalling brick and crumbling mortar lower down the stack. Catching it at the flashing stage keeps the repair small. Left alone, it turns into a masonry job.
Chimney Crown Repair in Salt Lake City
Chimney Crown Repair in Salt Lake City addresses the concrete cap on top of the stack, and it’s one of the most overlooked causes of water damage in older homes here. The crown sheds rain away from the flue, and when it cracks, water runs down inside the chimney instead of off the sides. A crown repair or rebuild typically runs $350 to $900 depending on the size of the stack and whether we’re patching or pouring a new crown with a proper overhang. Catching a hairline crack early is far cheaper than replacing a waterlogged flue liner later.
Cracks, Spalling, and Missing Overhang
A crown with no overhang lets water run down the face of the brick. We look for cracks wider than a hairline, concrete that’s flaking off, and a cap that was poured flush with the flue instead of sloping away from it. Any of those means water is getting in.
Rebuilding Rather Than Patching
When the crown is crumbling badly or the top courses of brick have spalled, patching won’t hold. Rebuilding the crown and the top of the stack with a proper slope gives the chimney a real roof again. We’ll show you which option your chimney actually needs.
Trusted Brands We Service in Salt Lake City
We work with a curated roster of professional-grade chimney brands: DuraFlex and HeatShield for liner systems and restoration, Gelco and Copperfield for caps, flashing, and venting accessories. These are the same materials CSIA-trained technicians use nationwide, and knowing how each one is specified and installed is part of the job. We don’t stock parts or keep a warehouse – we spec the right product for your flue and arrange it, which means fast turnaround on the repair once we’ve agreed on the plan. The right liner, installed right, is the whole point.
See the difference
Before
After
Before
After
Before
AfterCommon Chimney Repair Problems We See in Salt Lake City Homes
- Cracked or missing clay-tile flue liners. The 19th- and early-20th-century brick homes across the city often still have their original clay-tile liner, and those tiles crack under heat cycling. A cracked liner lets heat and creosote reach the framing, which is a fire risk, not a cosmetic issue.
- Inserts and stoves dropped into flues never sized for them. It’s common in Salt Lake City’s older homes to find a gas insert or wood stove vented into a coal-era flue that was never lined or is undersized for the appliance. The symptom is poor draft and smoke rolling back into the room, especially on cold days.
- Spalling mortar and loose brick from freeze-thaw winters. Water gets into the joints, freezes, and pops the mortar loose, and canyon winds drive rain against the stack from the side. Repointing and tuckpointing keep the masonry sound before the damage spreads.
- Failed crowns and flashing on aging brick. A cracked crown or lifted flashing lets water into the stack every time it rains or snows. Combined with the city’s hard winters, small roof-line leaks turn into liner and masonry damage fast.
Pricing for Chimney Repair in Salt Lake City, UT
Repair pricing here reflects the age of the housing stock. Mortar repointing typically runs $400 to $1,200 depending on how many square feet of joint need doing. Chimney waterproofing runs $300 to $650. Crown repair, as noted above, sits in the $350 to $900 range, and flashing repair in the $250 to $550 range. A full rebuild of a badly deteriorated stack is a larger job and gets priced per the written estimate after we’ve seen the chimney. What moves the number is access, height, how much masonry has spalled, and whether relining is needed. The estimate is free and the written proposal sets the final price – the ranges above are typical, not a quote.
We Also Serve Cities Near Salt Lake City
We work throughout the Salt Lake Valley, including West Valley City, Emigration Canyon, West Jordan, and Granite. If you’re just outside Salt Lake City and your chimney needs repair, call and we’ll confirm coverage. You can also read more about our chimney repair work and what a visit includes.
Serving Salt Lake City, UT – Our Local Coverage Area
We serve Salt Lake City and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs About Chimney Repair in Salt Lake City
It’s usually a repair, not a sweeping problem. When smoke rolls back into the room on cold days, the cause is typically a flue that’s undersized for the appliance, a liner that’s cracked or missing, or an insert dropped into a coal-era stack that was never lined for it. A sweep clears creosote, but it won’t fix poor draft. Call (877) 404-8451 and we’ll run a camera down the flue to find the actual cause.
You should be able to see the evidence yourself before you agree to anything. We run a camera inspection and show you the footage, and we won’t recommend relining or a rebuild without it. If the chimney can safely wait, we’ll tell you that too. Call (877) 404-8451 for a free estimate – you’ll know what your chimney actually needs before you spend a dollar.
A cracked crown shows up as visible fissures in the concrete cap, flaking concrete, or a cap with no overhang where water runs down the brick. Failing flashing looks like lifted or rusted metal at the roof line, gaps where the flashing meets the masonry, or water staining on the sheathing inside the attic. Either one lets water into the stack. Call (877) 404-8451 and we’ll check both.
Yes. A gas insert needs a properly sized liner matched to the appliance, and an old coal-era flue almost never has one. Venting a gas appliance into an unlined or oversized flue causes poor draft, backdrafting, and it lets moisture and heat reach the masonry. The liner is what makes the appliance vent correctly. Call (877) 404-8451 and we’ll check what’s actually in your flue.
Because during an inversion the valley traps smoke and fine particulate under the Wasatch Front cap, and a fireplace that backdrafts adds to the problem inside your own home. A smoking, backdrafting fireplace is often a venting and liner issue surfacing in the exact months burning is discouraged. That makes an accurate inspection a safety and air-quality matter, not just maintenance. Call (877) 404-8451 – estimates are free.
If your chimney needs repair in Salt Lake City, call (877) 404-8451 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. We work throughout Salt Lake City and the surrounding valley, and we’ll show you exactly what your chimney needs before any work begins.
Written by the team at Chimney Sweep West Jordan.